fbpx

Turbine Systems

Turbine Systems

Gas Turbines

Micronet plus

Network Components
    – RTN gateway
    – Linknet HT
    – RTC NET

Fuel Metering Valves
    – 3103/3171
    – GS6-GS16
    – LQ50
    – LQ25T
    – 3151A Water valve

Heavy frame Hydraulic fluid control systems
    -Sonicflo valve
    -Gas stop/Ratio valve
    -Linear actuator
    -Liquid stop valve

Shut Off Valves
    – GSOV25HT
    – LSOV

Hydraulic control

Digital Valve Positioner (DVP)

VSV VGV PUMP

Secure Remote Access (RAP)

Does your Turbine System, Electronic Control or Turbine Actuator need SERVICE, OVERHAUL or MAINTENANCE?

 

PJ Diesel Engineering A/S is a distributor and independent service facility for Woodward Inc and has been overhauling, servicing and reconditioning Turbine Systems, Electronic Controls and Turbine Actuators for the past 30+ years. Therefore, we have extensive experience and knowledge in this field and within all the known Brands.

Woodward supplies a range of products (controls, valves, actuators, safety systems, auxiliary, and combustion systems) for gas and steam turbines and compressors.

We strive to reduce total installed/operating cost and emissions while improving availability, efficiency, start performance and operating range. Woodward has the longest legacy of any control’s supplier in the industrial rotating equipment market. We continuously invest in bringing innovative solutions to real market needs. Our focus is on providing value to our original equipment manufacturer (OEM), packager and end user customers through combining our knowledge of controls, auxiliaries and combustion systems to drive optimization through simplification and integration.

Electronic Controls

Control Systems for Gas and Steam Turbines and Compressors

Control hardware/software for easy development, commissioning, startup, and operation.
Woodward programmable and configurable control systems for gas and steam turbines are purpose built with simplex, dual redundant and TMR options. All Woodward controls are designed to operate gas turbines, steam turbines, or integrated turbine/compressor systems. While standard I/O is built into the units, each control has options for communication with distributed I/O modules to provide extended application flexibility.

Extensive experience and customer diversity has resulted in the integration of most digital communication protocols. Finally, our Graphical Application ProgrammingGAP Software is designed for turbine and compressor control. The software allows control engineers, not software programmers, to develop applications in an easy-to-use, error-checking environment.

 

MicroNet Plus

The MicroNet™ Plus control system is a flexible, state-of-the-art digital control system designed specifically for prime mover control applications such as:

 

      • Gas Turbine Control
      • Steam Turbine Control
      • Compressor Control
      • Hydro Turbine Control
      • Diesel and Gas Engine Control

 

MicroNet Plus™ features, including redundant or simplex CPUs, modular I/O, flexible software environment, and highly accurate time synchronization make it ideal for its target markets:

      • Power Generation
      • Process Industries
      • Oil and Gas Exploration
      • Marine Transportation

 

MicroNet Plus™ control system flexibility and modularity adapt from simple applications with limited I/O to the most complex applications and processes with extensive I/O. The I/O modules and application software provide the control engineer with the flexibility to control or monitor every parameter and process of typical applications, including:

 

      • Speed and Load Control
      • Temperature and Process Control
      • Combustion Control
      • Anti-Surge Control
      • System Sequencing and Package Auxiliary Control
      • Alarm + Shutdown annunciation

 

Turbine Actuation

VariStroke Linear Electro-Hydraulic Actuators for Steam Turbines. Woodward solves steam turbine users’ #1 reliability problem . . . dirty oil!

The patented dirt tolerant and self-cleaning technology of Woodward’s VariStroke actuators ensure greater overall reliability of your steam turbine. The VariStroke Line of linear electro-hydraulic valve actuators operate mechanical-drive or generator-drive steam turbines. These linear actuators utilize a low-pressure, hydraulic oil source (typically turbine lube oil) to provide output shaft force. Their superb accuracy and resolution make them ideal for steam valve control and related turbine speed and load control, where turbine up-time and availability are essential.

The VariStroke line is configurable via a simple user-friendly, computer-based PC service tool, allowing users to easily configure, calibrate, and adjust all internal functions and response settings. It’s integrated driver includes a 4-20 mA output channel to indicate output shaft (control valve) position, as well as unit alarm and shutdown relay outputs for use as unit health and status indications. The 4-20 mA demand inputs and dual-redundant shaft position sensors allow it to continue to operate even with demand input or feedback sensor failures, ensuring extended run-times between forced outages and on-line system repair.

The total installed cost for this fully integrated actuator is low, because it is completely assembled and tested at the factory, greatly reducing OEM and end-user fabrication, testing, and site assembly time. In retrofit applications, the VariStroke actuator can be used to directly replace the existing servo system. This saves costly repairs to existing and aging servos, eliminates the difficulty of obtaining spare parts for obsolete equipment, and reduces calibration time and difficulty.

If your Turbine is not performing according to specification and requirement, you should contact a service provider immediately!

PJ Diesel Engineering A/S is Woodward AISF Authorized Independent Service Facility and distributor for governors, actuators, and turbine valves in Denmark, Estonia, Faroe Islands, Finland, Greenland, Iceland, Latvia, Lithuania, Sweden, and coastal area of Poland for marine applications.

 

Our core competences

 We are specialised within the Woodward product range:

      • Governors and electronic controls
      • Gas and steam turbine control
      • Valve services
      • Industrial gas turbine control
      • Power management

Woodward supplies a range of products (controls, valves, actuators, safety systems, auxiliary, and combustion systems) for gas and steam turbines and compressors.

We strive to reduce total installed/operating cost and emissions while improving availability, efficiency, start performance and operating range. Woodward has the longest legacy of any control’s supplier in the industrial rotating equipment market. We continuously invest in bringing innovative solutions to real market needs. Our focus is on providing value to our original equipment manufacturer (OEM), packager and end user customers through combining our knowledge of controls, auxiliaries and combustion systems to drive optimization through simplification and integration

 

We offer service for all Large Engine Control Modules - Our Woodward trained, and certified service engineers and service partners can assist on short notice.

 

We are ready to help you

 

Send Message

 

Circular flow and Exchange Service

 

Imagine a shared response program unlocking the value of unused assets and saving you from stockpiling key components for urgent repairs.

Within PJ Diesel Engineering A/S you can join services with other end-users minimizing stock expenses, and at the same time maintaining full flexibility and the advantage of externalizing the risks. Through our exchange program expensive individual ownership costs and delivery time is reduced with shared acknowledged access to key components.

Read more about our EXCHANGE SERVICE

 

 

 

 

Long- and short-term benefits

 

    • Improving service by enabling programmed maintenance and emergency response
    • Reduce dependency from shore facilities
    • Eliminate delivery time (Time required for repairs from shore)
    • Plug and play solutions
    • Risk reduction
    • Reduced operational cost
    • Elimination of expensive inventory
    • Fixed prices on exchange units - easy budget planning
    • 24 months liability for Shortages and Defects
    • High availability because of inventory at PJ Diesel Engineering A/S facilities
    • Not stocking expenses
    • No new unit investment
    • Full report and IMO/EAIAPP Validation
    • Repairable damages all included in SEU (Service Exchange Unit) A solution with no extra costs
    • Elevating from supplier to service partner (Trusted supplier)
    • Responsible and sustainable Supply Chain Management

 

A vast stock of genuine Woodward spares and Governor test stands

PJ Diesel Engineering A/S meet all the requirements for immediate service without delays. We further deliver field services for Woodward components for inspection, troubleshooting installation and commissioning.